Important Plumber Insights for Bathtub Installation
Important Plumber Insights for Bathtub Installation
Blog Article
We've stumbled on this post on Tools You Need to Install a New Bathtub listed below on the web and accepted it made perfect sense to talk about it with you over here.
Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a new one is also a reasonably tough job. If the old bathtub is easily available, the task can relocate easily; if you need to open a wall surface to get rid of the old bathtub as well as place the new bath tub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and also embeded in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to take into consideration using one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This article will certainly help you set up a new bathtub in your restroom if you have actually currently bought a new bathtub and do not need to change the arrangement of your previous supply of water pipelines.
Your devices and also material checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is detach the water system. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the limited accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap as well as the sink. Safeguard the faucet in place with the maker offered backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the spirit level checks out level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipe by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply and examine all joints as well as new pipework for leakages and tighten them if needed. Fill the bath tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bathtub should wait until the bathtub has actually been utilized a minimum of once as this will settle it into its last position.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, causing the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking a few minutes to read through our content. Liked our review? Please share it. Let somebody else discover it. We love reading our article about How to Install a Bathtub.
Prioritize your plumbing; call us. Report this page